A Vance company - serving Boulder City, NV

Mighty Mule Gate Motor Replacement in Boulder City, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Mighty Mule Gate Motor Replacement: The Boulder City Owner’s Guide

We replace Mighty Mule gate motors in Boulder City for most single-arm and dual-arm residential units, and the installed price typically runs between $850 and $1,600 depending on the model, mount condition, and hardware. Most jobs can be scheduled same-day when we’re working a Boulder City route, and every one starts with a written price agreed before a tool comes off the truck. You also get a photographed record of what came off and what went in.

Call (844) 320-7587

Owners rarely know the motor is the problem until something stops the gate. The usual scene: the gate goes halfway and reverses, or the arm runs but the gate doesn’t move, or one morning it clicks and stays put. In Boulder City, where summer heat soaks into a metal gate arm for six straight hours a day, the failure often traces to heat-degraded gear lubricant inside the housing, not to a dead control board. We check both before quoting a replacement.

Which Mighty Mule Models This Applies To

Most Mighty Mule replacements we see in Boulder City fall into the MM series of single-arm swing openers and the FM series of heavier dual-arm units, plus a run of older units still working on borrowed time. Matching the right part starts with the model tag on the bottom of the control box, not the arm. If the tag is faded or missing, we identify the unit by plate dimensions, arm travel, and the layout of the control board itself. That last detail matters more than people expect: the board layout tells us which generation of the housing we’re dealing with, and generations don’t swap cleanly.

The OEM versus aftermarket call is where owners lose money. Genuine Mighty Mule arms carry a specific spline and mounting pattern, and a generic arm with a close-looking spline will fit, run for a few weeks, then chew the output shaft and strand you. We fit aftermarket-only on select internals (motor brushes, small assemblies) where the quality genuinely matches. For the arm and the control board, we recommend genuine or a proven equivalent, and we tell you which is which before you approve anything. The same reasoning applies on the other brands we service, including LiftMaster, Ghost Controls, and DoorKing.

Vance Gate Repair Boulder City is an independent service provider. We aren’t affiliated with and aren’t authorized by Mighty Mule.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Mighty Mule Gate Motor Replacement Is Failing

Technician performing professional gate motor and opener repair service
Signs Your Mighty Mule Gate Motor Replacement Is Failing
  • The gate reverses before closing fully. A misread limit switch or a broken obstruction sensor interrupts the close command. We pull the readings before swapping parts, since a limit adjustment is often the whole fix.
  • Clicking, no motion. The motor is calling, but the start capacitor has failed or the gear set is stripped. A capacitor is cheap; a stripped gear set means the arm comes off.
  • Slow, labored travel. In Boulder City, this usually traces to heat-thickened lubricant or a binding hinge on the gate leaf, not to a weak motor. We isolate the motor from the gate before assuming it’s the unit.
  • One arm dead on a dual-arm unit. On a two-arm system, a single dead arm usually signals a board-level fault on one channel. Testing that arm on a bench tells us whether the arm or the board is at fault.
  • Photosensors won’t hold. A misaligned photo-eye (the infrared beam that stops the gate if something crosses the path) or a bad splice in the wiring brings the gate to a halt by design. We photograph the receiver alignment and the splice points.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
BeforeBefore
AfterAfter

Replacement Cost & What’s Included

Most Mighty Mule motor replacements in Boulder City land between $850 and $1,600 installed. A single-arm unit on intact mounting typically sits at the low end. A dual-arm unit, a rusted or failing mount bracket, or a board-and-arm combination pushes toward the top. If the gate leaf itself binds or the hinge posts need work, that’s priced separately, and we tell you which line is which before we start.

Item Typical range (installed)
Single-arm Mighty Mule motor replacement $850 – $1,150
Dual-arm Mighty Mule motor replacement $1,200 – $1,600
Control board replacement (with motor upgrade) Add $180 – $320
Mount bracket repair or replacement Add $95 – $250

Under Haven Standard Clause 1, that price is written and handed to you before any work starts. No “call for a quote” and no surprise invoice. And under the 365-Day Done Right Promise, if the unit fails within a year, we make it right at no additional charge. You also get a documented photo record: the old part number, the new one, and the limit-switch positions we set.

DIY or Call Us?

professional gate repair service
DIY or Call Us?

You can safely check the obvious things: battery voltage at the control box, whether the arm grinds or runs clean with the gate disconnected, and whether a visible limit switch is loose. Those checks take ten minutes and narrow the problem down.

What we’d steer you away from is opening the motor housing, bypassing the obstruction sensor, or resetting the limit switches by guesswork. The gate carries real force, and a limit set wrong will either jam the leaf against a stop or drive past the open position into a stall. On a dual-arm unit, pulling the wrong arm without isolating it can send the other leaf moving while you’re in the swing path. That’s where DIY gets expensive. If the unit is old enough that the gear set is already worn, a replacement is the honest answer. Call (844) 320-7587 for a free estimate.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Need Gate Repair help nationwide? Licensed & insured · within the hour response · free estimates
Call (844) 320-7587
Local Service Coverage

Request a Free Estimate in Boulder City

Tell us what you need - Vance Gate Repair Boulder City responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch