Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Repair in Boulder City: What to Know First
We repair Ghost Controls gate operators in Boulder City as an independent service provider, and most single-issue repairs are finished in one visit. Typical jobs run $185 to $540, and the exact flat price is written and handed to you before any work starts. Whether your Ghost Controls arm has stopped reversing, the keypad quit taking codes, or the gate stalls halfway, this page covers what actually fails on these units in Boulder City and what the fix involves. Call (844) 320-7587 and a live person answers, day or night.
How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls built its reputation on homeowner-installable swing operators, and those same design choices shape how their units fail. Here are the five failure modes we see most often in Boulder City, and what we do about each.
- Limit switches drifting out of position on the AXO and TSS1 series. Ghost Controls sets travel limits with mechanical stop cams rather than an optical encoder, so a slightly loose cam lets the gate creep past its set point and either slam or reverse short. We measure the actual cam position, reset travel to the correct degree of arc, torque the hardware, and photograph the new setting so the next technician starts from evidence instead of guesswork.
- Control-board corrosion from summer heat and dry-season dust. The controller housing on a Ghost Controls unit vents at the bottom, and in Boulder City the fine desert dust that blows off the washes collects on the board while afternoon heat cycles the enclosure. We’ve opened AXO boxes where dust had bridged two terminals. Our fix is a board clean and dielectric treatment, then a check of the seal and mounting angle, since a unit mounted in full afternoon sun runs far hotter than the same unit in shade.
- Arm bushing wear on the medium-duty linear arm. The articulated arm’s pivot bushings take the whole weight of a hollow-tube or wood gate, and on a heavier gate they wear faster than the motor ever will. You’ll hear a knock at the start of travel. We replace the bushings and re-grease the pivot points rather than selling a whole new operator, which is the honest call on most of these.
- Battery and solar failures mistaken for motor failure. A large share of Ghost Controls systems in Boulder City run on the 12V battery with an optional solar panel, and when the battery weakens the symptom looks like a dead motor: the gate moves slowly or not at all. We load-test the battery and check solar output before we touch the operator, because charging a customer for a motor that wasn’t broken is not something we’ll do.
- Accessory wiring and photo-eye misalignment. Keypads, wireless transmitters, and safety photo-eyes (the infrared beam that stops the gate if something crosses the path) fail at the connection point more often than inside the device. We trace the low-voltage wiring with a meter, correct any misalignment, and leave a wiring diagram of what we found so the next person doesn’t have to rediscover it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Ghost Controls Gate Repair Process

- 1
Call and diagnosis. You describe the symptom, a live person takes the call, and we book a visit. We ask what model and power setup you have so the technician arrives prepared.
- 2
On-site testing. The technician tests the operator, arm, battery, solar input, and every accessory, then photographs the readings. You hear the diagnosis before any repair is priced.
- 3
The parts decision. We lay out OEM versus quality aftermarket parts in plain terms. If an aftermarket board or arm meets the spec, we say so and price it. If OEM is the right call for your unit, we say that too. You choose, and we never steer a repair toward replacement when repair is what’s needed.
- 4
The repair. We complete the work to the agreed scope, with the flat price already in your hand.
- 5
The test. Every function is cycled and checked: full open, full close, reversal on obstruction, and accessory response.
- 6
The record and the guarantee. Before we leave, you get a photo log of what we found, adjusted, and replaced, plus the part numbers installed. The repair is covered by our 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
After
Before
AfterWhat Ghost Controls Gate Repair Costs in Boulder City
Here is what common Ghost Controls repairs typically run. These are real ranges, not teasers, and the exact price for your gate is written before work begins.
| Repair | Typical range |
|---|---|
| Limit switch reset and travel calibration | $185 – $260 |
| Control board clean, seal, and accessory wiring repair | $220 – $390 |
| Arm bushing replacement and pivot service | $240 – $380 |
| Battery and solar charging system repair | $210 – $430 |
| Photo-eye, keypad, or transmitter diagnosis and fix | $185 – $320 |
| Control board replacement (OEM or quality aftermarket) | $340 – $540 |
What moves the price: gate weight and type (a solid wood gate stresses the arm more than hollow tube), whether the operator sits in full sun, and whether the existing wiring is sound or needs repair. If another company has handed you a written estimate, bring it and we’ll review it at no cost. Call (844) 320-7587 for a free estimate and get the price in writing.
Why Boulder City Homeowners Call Vance Gate Repair Boulder City for Ghost Controls Work

Three things separate our Ghost Controls work from a general gate call. First, our technicians handle Ghost Controls as one of nine automation brands we service, so we can work on whatever motor is already on your property – Ghost Controls today, LiftMaster, Mighty Mule, or DoorKing if you ever change systems – without pushing you toward a brand we prefer. Second, we document every job: a photographed record of limit positions, wiring, and installed part numbers, left with you, so no future technician has to guess. Third, the 365-Day Done Right Promise means if the repair isn’t right, we make it right for a full year with no additional charge. A live person answers the phone 24/7. Call (844) 320-7587.
FAQs
Yes, and we’re careful about it. Because we’re an independent Ghost Controls service provider and not the manufacturer, we note what’s covered and proceed in a way that doesn’t void your warranty, using OEM parts when that’s what keeps coverage intact. Ask us to check before we start.
For parts we don’t carry in stock, we order the specific OEM or aftermarket part for your model; ordinary control boards, arms, bushings, and batteries usually arrive within a few days. We don’t promise same-day on a part we have to order, and we’ll tell you the lead time before you commit.
That’s usually a limit switch or control board issue, not a failed motor. It can also be a weak battery on a solar system. We test all three on-site and give you a written price for the actual cause before repairing.
Repair is the right call on most units we see. A board, arm, or battery fix costs a fraction of a new operator and keeps a system that’s otherwise sound. We only recommend replacement when a component genuinely can’t be serviced, and we’ll show you why.
Single-issue repairs are often scheduled within one visit, and a live person answers at any hour to book it. Call (844) 320-7587 and we’ll confirm the earliest time and the flat price in writing.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City and nearby areas.