A Vance company - serving Boulder City, NV

Ghost Controls Keypad & Intercom Repair in Boulder City, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Keypad & Intercom Repair: The Boulder City Owner’s Guide

We repair and replace Ghost Controls keypads and intercom units on Boulder City driveway gates, and most installed keypad jobs land between $210 and $385 depending on the unit and whether the low-voltage wiring run has to be re-terminated. Intercom repair runs higher, generally $275 to $520, because a two-way audio unit carries its own power and signal pair. Because we work on Ghost Controls alongside eight other automation brands, we can match the right part to what’s actually on your post instead of pushing you toward a new operator.

Call (844) 320-7587

Owners usually find this failure the same way: the gate still opens from the car remote, but the keypad code stops taking, or the intercom crackles and goes dead when someone presses the call button. Boulder City’s wind-driven grit and summer heat get into the keypad’s membrane and the intercom’s speaker grille, and that’s where the trouble tends to start.

  • The first thing to know: we’re an independent service company, not affiliated with Ghost Controls. We service their equipment, we don’t represent them.
  • Second: the price is written and handed to you before any tool comes out, and you get a photo record of what we found and what we installed before we leave.

Which Ghost Controls Models This Applies To

Ghost Controls builds its keypads and intercom accessories around the same control-board family across its single and dual swing operators, so in practice a wireless keypad that talks to an AXS or TSS-series board will generally pair the same way once you’re on the right frequency. The important variable is the receiver side, not the letter on the housing. Keypads ship in a couple of radio configurations, and a replacement that doesn’t match the operator’s receiver will look identical on the post and simply never trigger the gate.

To identify what you have, look for the model tag on the underside of the gate operator control box and the sticker on the back of the keypad or intercom. Note the serial prefix, not just the model name. If the sticker is sun-bleached and unreadable (common on west-facing posts here), we photograph the board, count the terminals, and match the part from that rather than guessing.

On the OEM-versus-aftermarket question, we’re blunt about it: a genuine Ghost Controls keypad is the safer choice when your operator is under warranty or when you want an exact fit in the existing mounting footprint. A quality aftermarket equivalent can be perfectly serviceable when the original housing is discontinued or the lead time is long, but you need to confirm the frequency and power spec before you buy. We tell you which category your part falls into before you spend anything.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

professional gate repair service
Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

Here’s what these parts actually do when they start going, and what’s usually behind it:

  • The code stops taking but the remote still works. That points to the keypad’s radio board or its battery, not the gate operator. If the remote opens the gate fine, the operator is healthy and the fault lives in the keypad.
  • Some keys respond, others don’t. Water or grit has gotten under the membrane. Heat and wind-blown dust are the usual culprits, and it’s a straight replacement rather than a cleaning job.
  • The keypad lights up but never sends. The unit has power but no signal, which is often a loose terminal in the control box or a receiver that’s stopped listening. It may be a wiring repair rather than a new keypad.
  • The intercom crackles, cuts out, or goes silent on the call button. A failing speaker, a corroded connection, or a power supply that’s sagging. Intercoms carry two separate circuits, and one can fail while the other still works.
  • Intermittent operation after rain or a cold morning. Moisture is bridging a connection inside the housing. It works until it doesn’t, and it usually gets worse before it gets better.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
BeforeBefore
AfterAfter

Replacement Cost & What’s Included

Most keypad replacements in Boulder City run $210 to $385 installed, and intercom repair or replacement runs $275 to $520. What moves you within that range: whether the existing low-voltage run to the post is good or needs re-pulling, whether the mounting footprint matches (a different housing can mean new holes and a fresh seal), and whether your unit is a simple code keypad or a full intercom with a call button and audio.

The price covers the part and the labor. It’s written down and agreed before work starts, so there’s no invoice surprise at the end. Under Clause 1 of our Haven Standard, you get the number in writing first. Every completed repair is covered by our 365-Day Done Right Promise, and every visit leaves you a photo log of what we found, what we set, and the part we put on. If you’ve got a written estimate from another company, we’ll review it free.

DIY or Call Us?

Technician applying sealant to a weathered metal gate post cap repair
DIY or Call Us?

You can safely check a few things yourself. Confirm the operator still opens the gate from a remote, test whether the keypad battery is dead, and look for obvious corrosion or a loose wire at the post. Replacing a keypad battery is fine to do on your own. What you shouldn’t do is open the operator’s control box and start moving low-voltage wires around, or work on the gate arm, without knowing what’s live. On a swing gate with a working operator, the arm can move under power when you’re not expecting it.

Where DIY goes wrong with this part is the pairing step. A new keypad that’s the wrong frequency or not properly learned into the receiver will sit there looking installed and do nothing, and people often buy a second one before they realize the first was never matched. That’s a $200 mistake we see more than we’d like. If the code and the radio spec aren’t confirmed, call us at (844) 320-7587 and we’ll tell you what you’re looking at before you buy anything.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Need Gate Repair help nationwide? Licensed & insured · within the hour response · free estimates
Call (844) 320-7587
Local Service Coverage

Request a Free Estimate in Boulder City

Tell us what you need - Vance Gate Repair Boulder City responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch