Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Welding & Fabrication: The Boulder City Owner’s Guide
We fabricate and repair the welded steel components that Ghost Controls gate systems attach to – cracked hinge posts, fatigued operator mounting brackets, failed chain-idler weldments, and bent gate frame members. In Boulder City, that work typically runs $240 to $680 installed, depending on whether we’re repairing on-site or cutting, fitting, and re-welding a bracket from scratch, and most straightforward bracket replacements can be handled the same day you call.
Owners rarely wake up knowing a weld failed. They notice the gate dragging at one end, hear a pop when the operator arm extends, or find that the Ghost Controls control board keeps hitting an obstruction fault at the same point in travel. That’s usually the mount shifting under load, not the motor. A bracket that’s been vibrating loose against a gate frame for two heating seasons will crack at the toe of the weld long before it looks obviously broken. We see this in Boulder City more than most places because of the temperature swing – triple-digit summers and cool desert nights work a weld like a hinge.
Which Ghost Controls Models This Applies To
Ghost Controls builds primarily for do-it-yourself and light-duty residential applications – the DTP1, DTP2, TSS1, and related single and dual gate operator kits. The welding and fabrication side of those systems isn’t branded by Ghost Controls at all; it’s the mounting post, the operator bracket, and the gate frame the arm attaches to. What matters is the geometry. A Ghost Controls arm bracket is drilled to a specific hole pattern and offset, and a bracket fabricated to Mighty Mule or LiftMaster dimensions won’t line up without either redrilling the operator arm or rebuilding the plate.
Identifying the right part starts with the label inside the control box lid – the model and serial tell you which arm length and bracket style the kit shipped with. From there, we measure the post diameter, the bracket offset from the hinge line, and the arm’s fully retracted and extended positions.
On the OEM-versus-aftermarket question: Ghost Controls factory brackets are fine, but for a Boulder City gate we’ll usually recommend a heavier-gauge fabricated bracket rather than a drop-in replacement. The original plate is commonly 3/16-inch steel, and on a gate that’s seen a decade of thermal cycling, stepping up to 1/4-inch with a gusseted corner is the difference between a five-year bracket and a fifteen-year one. We’re an independent service provider, not affiliated with Ghost Controls, so we’re free to recommend whatever actually holds up.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Welding & Fabrication Is Failing

- The gate sags at the latch end. That’s usually not the hinge pin – it’s the weld where the hinge post meets the gate frame, thinning from rust creep or fatigue. Left alone, it loads the operator arm unevenly and shortens motor life.
- Operator arm binds or pops mid-travel. The mounting bracket has shifted or the weld cracked underneath it, changing the arm’s geometry. Ghost Controls boards often report this as an obstruction fault at the same gate position every cycle.
- Visible rust bloom around a weld toe. Coronary rust weeping from a weld line means moisture has been wicking in along the joint. In Boulder City’s low humidity this happens from irrigation overspray and sprinkler splash more than rain.
- Bracket flexes when you push the gate by hand. Any movement at the operator mount is a weld or a bolt that’s lost preload. A bracket that flexes a quarter-inch under hand pressure will flex far more under motor torque.
- Cracks running from the corner of a fabricated joint. Stress concentrates at corner welds on gate frames and idler plates. A hairline crack there grows with every cycle, and it can fail suddenly when the gate is under load.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Welding and fabrication pricing in Boulder City breaks down by scope, and we write it out before a torch is lit – the flat number is handed over on paper before any work starts. Here’s the range owners typically see:
- Crack repair on an existing weld: $240 to $380 – grind, prep, re-weld, dress, and touch up.
- Operator bracket replacement (fabricated to Ghost Controls arm geometry): $320 to $520, including drilling and fitting.
- Hinge post or gate frame member repair: $380 to $680, depending on access and whether the gate has to come off its hinges.
- New gusseted bracket fabricated from scratch: quoted per measurement, since this is a build rather than a repair.
What drives the range: material gauge, whether we can weld in place or must remove the member, access to the weld, and finish work. Parts and labor are itemized separately on the written price. Every completed weld is covered by the 365-Day Done Right Promise – if a repair isn’t right, we make it right at no additional charge.
DIY or Call Us?

There’s a safe list and an unsafe list, and we’d rather you know which is which. On the safe side: you can inspect welds with a flashlight for rust bloom and hairline cracks, check bracket bolts for play with a wrench, and photograph any crack so you have a record. That’s diagnostic work and it costs nothing.
Where DIY goes wrong is the actual welding. Arc welding and cutting carry real burn, fire, and eye hazards, and a bracket fabricated on a workbench with no reference to the arm’s swing geometry will bolt up crooked and fight the operator for its whole service life. We’d rather see you book a technician than get hurt or waste a weekend. Most straightforward bracket replacements are same-day calls, and the number to reach us is (844) 320-7587 – a live person answers around the clock.
FAQs
A properly fabricated bracket should last 10 to 15 years. The factory bracket on a Ghost Controls kit often gives 6 to 10 in Boulder City’s climate because the daily temperature swing stresses the thinner original steel. If you’re seeing movement after five years, it’s not unusual.
Often yes. Surface cracks at a weld toe can be ground out and re-welded if the surrounding metal is sound. If the underlying steel has thinned from rust, we recommend rebuilding the bracket rather than welding over a tired joint, and we’ll tell you which we found before we touch a torch.
Most straightforward bracket repairs take 2 to 4 hours on-site. Gate frame or hinge post work that requires removing the gate can run half a day. We quote the time window with the written price, so you know what to plan around.
For Ghost Controls-compatible brackets we either repair what’s there or fabricate a replacement to your measured arm geometry, using heavier-gauge steel than the original where it makes sense. We don’t carry parts on a truck – we fabricate or source the correct part for your specific kit. Call (844) 320-7587 for a free estimate.
If a Ghost Controls gate in Boulder City is binding, sagging, or throwing obstruction faults at the same spot every cycle, it’s worth a look before the weld fails completely. Call Vance Gate Repair Boulder City at (844) 320-7587 for a free estimate – we’ll put the scope and the price in writing before any work starts, document what we found and what we fit, and stand behind it for a full year.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City and nearby areas.