Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Repair in Boulder City: What to Know First
We provide independent DoorKing gate repair in Boulder City, and most DoorKing calls we run here are handled on the first visit. Common swing and slide repairs – limit-switch resets, photo-eye realignments, hinge and post work, motor and control-board service – typically land between $180 and $650 depending on the series and whether a control board or motor needs replacing. We’re an independent DoorKing service provider, not affiliated with or authorized by DoorKing, and we work on whatever actuator or operator is already on your property.
This page is for Boulder City homeowners with a DoorKing operator on their driveway gate who want the price visible before they call, a written scope before anyone touches a tool, and a documented record when the technician leaves. Call (844) 320-7587 and a live person answers, day or night – no voicemail, no callback queue.
How DoorKing Products Fail – and How We Fix Them
DoorKing operators fail in specific ways that differ from LiftMaster or Mighty Mule units, and knowing which series you have shortens the diagnosis. Here’s what we actually find in Boulder City.
- Model 6400 swing operators – arm bracket fatigue. The articulated arm on a 6400 series swing gate takes load every cycle, and the bracket-to-post bolts work loose over years of thermal expansion. We’ve pulled brackets in Boulder City where two of four bolts had backed out entirely. Our fix: torque to spec, replace any stripped hardware, and photograph the bracket before and after so the next tech has a baseline.
- Model 1601 / 1602 slide operators – limit-switch drift. Slide operators rely on physical limit switches to know where travel ends. In a Boulder City summer, the gate track expands and the switch position drifts past the point it was set at. The gate runs hard into the stop, the controller faults out, and sometimes the operator throws a code the owner can’t decode. We reset the limit, test full open and full close, and log the reading.
- Photo-eye and safety-edge faults across all series. DoorKing photo-eyes (the infrared beam that stops the gate if something crosses the path) go out of alignment when a post settles or a bracket loosens. A gate that reverses mid-travel for no visible reason is usually this, not a board problem. We realign, verify the beam, and test both directions before we leave.
- Control-board moisture ingress on exterior enclosures. DoorKing control boxes mounted on a fence post face wind-driven dust and the occasional summer storm. Boards that show corrosion at the terminal strip usually need replacement, not a cleaning. We test the board at the terminals, confirm the fault, and quote the board before pulling it.
- Weld and rust failures at hinge and post connections. The gate leaf itself (not the operator) is often the source of a “my gate is failing” call. Weld cracks at the hinge plate and rust at the bottom rail are common on older steel gates in Boulder City’s dry-then-wet cycle. We weld, treat the rust, and refit the hinge so the operator isn’t fighting a binding gate.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our DoorKing Gate Repair Process

- 1
Call and intake. You describe the symptom, we ask for the DoorKing model number if it’s visible on the operator housing, and we give you a written price range before we schedule.
- 2
On-site diagnosis. The technician tests the operator at the terminals, reads the limit switches, checks the photo-eyes and safety edges, and checks the gate leaf itself for binding or weld cracks. Findings are photographed.
- 3
Written scope and price. Before any part is ordered or any tool is picked up, you get the scope and the flat price in writing. OEM DoorKing parts versus quality aftermarket is a line item, not a surprise – we’ll tell you honestly when OEM is worth it and when it isn’t.
- 4
The repair. Limit resets, photo-eye realignment, bracket hardware, board or motor replacement, weld and hinge repair – done to spec, with the part number recorded on the invoice.
- 5
Full-cycle test. Open, close, reverse test with an obstruction, safety-edge check, manual release check. The gate has to work both directions before we call the job done.
- 6
Documented record. You get a photo log of every adjustment and a written record of what was replaced. Under the Haven Standard, every visit carries that record at no additional charge. The 365-Day Done Right Promise covers the repair for a full year.
See the difference
Before
After
Before
After
Before
After
Before
AfterWhat DoorKing Gate Repair Costs in Boulder City
Every DoorKing repair here is quoted in writing before any work starts, so the numbers below are what you’ll actually see on the estimate.
| DoorKing repair | Typical range |
|---|---|
| Photo-eye or safety-edge realignment | $180 – $280 |
| Limit-switch reset or replacement | $200 – $340 |
| Hinge and post weld repair | $280 – $520 |
| Control board replacement | $380 – $650 |
| Swing or slide motor / actuator replacement | $600 – $1,500 (varies widely by series and bracket condition) |
What moves the price: the series (a 6400 swing operator and a 1601 slide operator don’t share parts), OEM versus aftermarket on a board or motor, condition of the arm bracket or hinge plate, and whether the gate leaf needs weld repair before the operator will run right. The estimate is free, and the price you’re quoted is the price you pay. Call (844) 320-7587 for an exact number on your DoorKing.
Why Boulder City Homeowners Call Vance Gate Repair Boulder City for DoorKing Work

Three things decide whether a DoorKing repair gets done right. First, the price is written before the work starts – no estimate over the phone with a different number on the invoice. Second, the technician has actually worked on DoorKing equipment and knows the difference between a dead control board and a limit switch that’s drifted 12 degrees past travel. Third, you get a record of what was done, photographed, so the next tech isn’t guessing.
We’ve repaired and installed more than 22,000 gates since 2014, each one with a written price and a documented record. Our technicians have up to 12 years of experience. We service nine automation brands – DoorKing, LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, Elite, and Mighty Mule – so if your property has a mixed setup or you’re not sure what brand you own, we can still handle it. A live person answers (844) 320-7587 around the clock.
FAQs
Every repair we complete is covered by the 365-Day Done Right Promise – if it isn’t right, we make it right within that year at no additional charge. DoorKing’s own manufacturer warranty on new parts is separate; we record the part number and install date on your invoice so you can claim it if eligible. Call (844) 320-7587 – estimates are free.
Most DoorKing repair calls we take in Boulder City are handled the same day. We answer at any hour, so a gate stuck open at night gets a live person, not a voicemail. Call (844) 320-7587 for the fastest dispatch.
Common parts – photo-eyes, limit switches, hardware, most control boards – we can usually source without a long wait. Less-common series-specific actuators may need to be ordered, and we’ll quote the timeline upfront in writing. We can also tell you when a quality aftermarket board is a sensible alternative to OEM on your specific model. Call (844) 320-7587 for a part check.
In most cases a DoorKing operator is repairable, and repair is what we’ll recommend unless the actuator itself is past saving. We quote repair first and only suggest replacement when the motor or gearbox can’t be brought back economically – and we’ll show you the diagnostic that led there. Call (844) 320-7587 with the model number for a straight answer.
A DoorKing gate that reverses mid-travel is almost always a photo-eye or safety-edge fault, not a control board, though we’ve seen both. A two-inch misalignment on a photo-eye after a post settles will trip the reverse every time. We diagnose and realign, then verify full travel. Call (844) 320-7587 for same-day service.
If your DoorKing operator is faulting, reversing, or running hard into its stops, we’ll diagnose it, quote it in writing, and leave a documented record when we’re done. Call Vance Gate Repair Boulder City at (844) 320-7587 for a free estimate.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City and nearby areas.