Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Motor Replacement: The Boulder City Owner’s Guide
DoorKing gate motor replacement in Boulder City typically runs $850 to $1,900 installed, depending on the model, the condition of the operator’s mounting pad, and whether the control board and safety devices survive the swap. We keep our schedule open for same-day calls on dead operators, and every price is written and handed over before a tool comes out. Most Boulder City owners discover the problem the same way: the gate stops mid-travel, the operator clicks but won’t move, or the arm stalls in the afternoon heat and starts working again after dark.
Key Takeaways
- Installed DoorKing motor replacement in Boulder City: $850 – $1,900, quoted in writing first.
- DoorKing compatibility is decided by model number and control board, not by the shape of the box.
- We change the operator; we don’t touch high-voltage wiring unless it’s part of the written scope.
- Every visit leaves a photo record of the old unit, the wiring, and the new settings.
- We service DoorKing alongside LiftMaster, Mighty Mule, Ghost Controls, FAAC, BFT, Linear, Viking, and Elite.
Which DoorKing Models This Applies To
DoorKing builds slide-gate and swing-gate operators that look similar on the outside and behave nothing alike underneath. The model number is stamped on the operator housing or printed on the label inside the control-box cover, and that number – plus the control board revision printed on the board itself – is what determines which replacement will work. A Model 6050 slide operator and a Model 6400 swing operator share a brand name and very little else. If the label is sun-faded or painted over, we photograph the housing, measure the gate leaf, and read the existing board before quoting anything.
On older DoorKing units still running in Boulder City, the honest question is OEM versus a quality aftermarket equivalent. We quote both where both exist, and we tell you which one we’d put on our own gate and why. One compatibility gotcha worth knowing: DoorKing control boards are revision-sensitive, so a replacement motor that bolts up perfectly can still refuse to run on a board set for a different revision. The board, the limit settings, and the motor travel have to agree. We check all three before the new unit goes in.
We’re an independent service provider. We’re not affiliated with DoorKing, and we don’t sell parts or carry stock on a truck – we source the correct replacement for your model and install it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Gate Motor Replacement Is Failing

- The gate stalls partway through travel, especially in the afternoon. Boulder City summer heat pushes the operator’s thermal overload into protection mode, and a motor with worn brushes or a tired capacitor will stall at 105°F but run fine at dawn. Intermittent midday stalling is usually the motor, not the gate.
- The operator clicks or hums but the gate doesn’t move. That’s often a failed start capacitor or a seized gearbox. On older DoorKing units a stripped nylon gear will let the motor spin and the gate sit still – cheap to diagnose, and it tells you whether the motor itself is finished.
- The gate reverses on its own or stops short of the limit. Usually a limit-switch or encoder problem. Sometimes it’s the board, sometimes the switch, and we read the limit position before touching anything so we know which.
- The arm or chain jumps, grinds, or jerks. Mechanical wear in the drive train. On a slide operator, chain stretch and sprocket wear show up as grinding before the motor dies; the motor may still be good and the drive train may not.
- The operator runs slow, then trips the breaker or blows a fuse. Electrical drag on a tired motor or a short in the wiring. This one gets checked before the gate is run again.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed prices for a DoorKing motor replacement in Boulder City:
| Job | Typical installed price |
|---|---|
| Slide-gate operator, like-for-like swap | $850 – $1,250 |
| Swing-gate operator, like-for-like swap | $900 – $1,400 |
| Swap with control board replacement | $1,100 – $1,600 |
| Swap plus safety device refresh (photo-eyes, edges) | $1,300 – $1,900 |
| Mounting pad repair or new anchor set | $250 – $600 |
The range is driven by the model, whether the old control board carries over, whether the mounting pad and anchors are sound, and whether the safety devices are still working. You get the part number and the flat price in writing before we start, and a written record of what was installed and how it was set when we leave. Every replacement is covered by our 365-Day Done Right Promise.
DIY or Call Us?

You can safely check a few things: confirm the model number, look for a tripped breaker or a blown fuse on the operator’s dedicated circuit, clear debris from the gate’s travel path, and photograph the limit switches before anything moves. What you shouldn’t take on is the operator swap itself. A DoorKing operator runs on line voltage, often with a backup battery and a control board wired to safety photo-eyes and edge sensors. Getting the high-voltage feed wrong or mis-wiring the safety devices can leave the gate running when a person is in its path. That’s a job for someone who does it every day, with the power verified off before a single wire is moved.
If your DoorKing operator is dead or failing, call (844) 320-7587. A live person answers, 24/7, and we’ll give you a written price before any work starts.
FAQs
A well-maintained DoorKing operator generally gives 10 to 15 years in a residential setting; in Boulder City’s heat and dust, expect the lower end of that unless the unit is shaded and kept clean. Dust on the drive train and sun on the housing both shorten life, and a yearly service check catches worn parts before the motor fails.
Often, yes. A failed capacitor, a bad control board, a seized limit switch, or a worn gear is a repair, not a replacement, and we’ll tell you which you’re looking at before recommending a swap. Call (844) 320-7587 and we’ll diagnose it and quote the repair first.
A like-for-like swap is usually a few hours, but the total depends on whether the mounting pad and wiring need work and whether the control board carries over. We schedule the job around what we found on the first visit and put the time estimate in writing with the price.
We match the part to your exact DoorKing model and board revision before ordering. We don’t stock parts or carry them on a truck – the correct unit is sourced for your gate, and the part number goes on your written record. Call (844) 320-7587 to get yours quoted.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City and nearby areas.