Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Welding & Fabrication: The Boulder City Owner’s Guide
Welding and fabrication on a DoorKing gate assembly in Boulder City typically runs $280 to $950 installed, depending on whether we’re re-welding a cracked hinge post, fabricating a replacement slide-gate roller carriage, or rebuilding a bent cantilever arm bracket. Straight weld repairs on accessible steel are usually done same day; fabricated parts need a measure-and-cut visit first. Most owners find us after the gate starts dragging, a hinge clangs on the swing, or the opener strains against a frame that has quietly lost its shape. We’re an independent provider, not affiliated with DoorKing, and we price every weld in writing before the torch comes out.
Which DoorKing Models This Applies To
DoorKing welding and fabrication work touches three families of equipment. The slide-gate operators (Series 9000, 9100, 9200 and the 6050/6400 lines) carry roller carriages, guide rollers and track brackets that take real lateral load, and those are the parts that crack on older steel gates under repeated slide cycles. The swing operators (Series 1500, 1600, 1800 and 6400) mount via a welded or bolted arm bracket or pad, and a bracket weld that fails lets the arm twist off axis. Pedestal and stand mounts for the 6000-series operate on welded steel posts that corrode at the base weld in desert humidity swings.
To identify the right part, start with the model plate on the operator housing (a stamped tag near the control box, usually) and measure the gate leaf width and post spacing before you order anything. DoorKing changes bracket geometry between series, and a bracket that looks right on a parts diagram can sit 1/2 inch off at the hinge. OEM fabricated parts fit the original design; quality aftermarket pieces save money on standard rollers and carriage bolts but often skip the load-bearing weld detail that the OEM bracket includes. For Boulder City gates, we recommend OEM or equivalent-gauge fabrication on any structural weld and aftermarket only on non-load-bearing hardware.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Welding & Fabrication Is Failing

- The gate drags or jumps mid-slide. That usually means a roller carriage weld has cracked at the axle boss, letting the roller cock and bind in the track. Left alone, the guide roller wears flat in a week.
- A hinge clangs on the swing. A hinge-post weld has failed and the leaf is riding on the pin instead of the weld. It sounds like a knock and gets worse with every cycle.
- The opener strains or reverses on a clean path. A bent cantilever arm bracket or a sagging fabricated carriage adds resistance the operator can’t overcome. The control board sees it as an obstruction.
- Visible rust tracking from a weld seam. Desert temperature swings pull moisture into weld pores, and rust blooms at the seam before the weld itself cracks. That rust line is where it will fail next.
- The gate leaf sits crooked at rest. A welded hinge or carriage plate has shifted, and the leaf no longer hangs square. The operator compensates until it can’t.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed welding and fabrication on DoorKing gates in Boulder City falls roughly in these ranges:
| Work | Installed range |
|---|---|
| Weld repair, cracked hinge or carriage (accessible) | $280 – $480 |
| Re-weld and re-align roller carriage | $350 – $620 |
| Fabricate replacement bracket or carriage | $520 – $950 |
| Pedestal or stand mount repair | $400 – $750 |
What drives the range: whether the part can be re-welded in place or has to come off the gate, whether the existing steel is weldable or too corroded, and how much realignment follows the weld. Every price is a written flat quote you see before we start. The weld is covered by the 365-Day Done Right Promise, and you get a photo record of the weld, the fit-up and the final measurement when we leave.
DIY or Call Us?

You can safely check a few things yourself: run the gate slowly by hand with the operator disengaged and feel for the drag point, look for rust lines tracking from a weld seam, and take a photo of the model plate on the operator to identify your series. What you shouldn’t do is weld or cut on a gate that’s still attached to a live operator. A loaded gate leaf under spring or counterweight tension can swing or drop when a weld lets go, and welding on the frame with the operator wired in risks damaging the control board through stray current. That’s not a scare tactic, just how the load works. Call (844) 320-7587 and we’ll come out, photograph what we find, and quote the repair in writing before anything gets torched.
FAQs
How long does a welded DoorKing gate repair last? A properly prepped and welded DoorKing hinge or carriage repair typically lasts 8 to 12 years in Boulder City conditions, depending on steel thickness and whether the weld is primed and sealed. Poorly prepped welds on corroded steel fail within a season or two, which is why we photograph the prep before we strike an arc.
Can you repair the failed weld instead of replacing the part? Often yes. Most cracked hinge and carriage welds on DoorKing gates can be re-welded and re-aligned if the surrounding steel is sound and thick enough to take a clean bead. If the parent metal is too far gone, we fabricate a replacement instead, and you’ll see that decision in writing before we commit to either route.
How long does the swap or repair take? A straightforward weld repair on an accessible DoorKing gate is a same-day job, usually two to three hours on site including the photo record. Fabricated replacement parts need a measure-and-cut visit first, with installation scheduled once the piece is ready, so plan on two visits for those.
How do you source the part? We measure the existing bracket or carriage and match it to the DoorKing series on your model plate, then source OEM or equivalent-gauge fabrication to the measured fit. For non-structural hardware we’ll sometimes use a quality aftermarket roller or bolt when it meets spec, and you get the part number written on the record.
Whether your gate is a DoorKing or one of the other brands we service – LiftMaster, Mighty Mule, Ghost Controls among them – call Vance Gate Repair Boulder City at (844) 320-7587 for a free estimate on your welding and fabrication repair. We’ll come out, photograph what we found, hand you a written price, and back the work with the 365-Day Done Right Promise.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City and nearby areas.