Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Keypad & Intercom Repair: The Boulder City Owner’s Guide
We repair and replace DoorKing keypads and intercoms in Boulder City, with most installed jobs landing between $285 and $720 depending on which DoorKing series you have and whether the wiring to the gate is sound. Emergency and same-day calls are available, and a live person answers the phone at any hour. The price is written and handed to you before any work starts. Most Boulder City owners discover the failure the same way: the code that worked for years suddenly stops, or the call button rings inside the house but nobody can hear the visitor on the other end.
Key Takeaways
- DoorKing keypad and intercom repair in Boulder City typically runs $285 – $720 installed, with the written price given before work begins.
- Most failures are the keypad membrane, the intercom speaker, or corroded terminal screws, not the whole unit.
- We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we work on the motor already on your property.
- Every repair is covered by the 365-Day Done Right Promise.
Which DoorKing Models This Applies To
DoorKing keypads and intercoms fall into a few family lines. The 1500 series is the standalone keypad with no phone connection. The 1810 and 1830 series add intercom and phone access. The 1802, 1803, and 1812 entrance controls cover apartment and multi-tenant setups. On the newer side, the 1835, 1837, and 1838 units combine keypad, intercom, and directory in one housing. Knowing your number matters because the faceplate cutout and terminal layout change between them, and a keypad that looks identical on the outside can have a different harness inside.
To identify yours, open the housing and read the label on the back of the circuit board or on the inside of the cover. Look for a four-digit model number followed by a revision letter. If the label is gone, measure the housing width and photograph the terminal strip. We work from that photo to match the part.
On the OEM question: DoorKing boards and membranes are the safest match for older units where every connector has to line up exactly. On current-production models, quality aftermarket keypad modules perform correctly and cost less. We compare both options on the written quote and let you decide, rather than defaulting to the pricier one. Vance Gate Repair Boulder City is an independent service provider and is not affiliated with DoorKing.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Keypad & Intercom Repair Is Failing

- Some keys work, others don’t. The membrane behind the buttons wears through in the spots pressed most often, which is usually the 1, 2, and 3 keys. This is a membrane failure, not a board failure, and it’s the most common reason a Boulder City keypad starts rejecting codes it used to accept.
- The gate opens from inside but the keypad does nothing. The relay inside the keypad or the low-voltage wire running to the gate operator has an open circuit. A meter test at the terminal strip tells you which one in about two minutes.
- The intercom rings, but the visitor’s voice is faint or gone. The speaker or microphone in the DoorKing housing has water damage or a cracked cone. Desert heat and the occasional hard rain of the Mojave basin age these faster than the electronics around them.
- Codes are rejected only in cold mornings or after rain. Moisture has reached the terminal screws or the keypad gasket has shrunk, and the connection goes intermittent. This one worsens quietly until the keypad stops entirely.
- The display is blank or shows scrambled characters. The power supply has sagged below spec or the board’s voltage regulator has failed. On a DoorKing 1835, a blank display with a live keypad usually points to the power module, not the whole unit.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for keypad and intercom work in Boulder City depends on the series and how much wiring has to be redone. Here’s how the ranges break down:
| Job | Installed Range | What It Covers |
|---|---|---|
| Keypad membrane and button pad replacement | $285 – $420 | New membrane, gasket, terminal cleanup, code reprogram |
| Full keypad unit replacement (1500-series style) | $390 – $560 | New unit, wiring to the operator, code setup |
| Intercom speaker or microphone replacement | $320 – $480 | New speaker or mic, seal, audio test |
| Combined keypad and intercom replacement | $520 – $720 | New head unit, harness, directory setup, gate test cycle |
The range moves on two things: whether the low-voltage wire from the gate to the keypad is intact and whether the operator will accept a new trigger cleanly. If the wire needs to be pulled, that’s quoted separately and shown on the written price. Parts and labor are listed as separate lines so you can see what you’re paying for. The 365-Day Done Right Promise covers the repair for a full year.
DIY or Call Us?

What you can safely check: whether the keypad has power (look for a lit display or a beep when you press a key), whether the gate opens from the interior control, and whether the terminal screws inside the housing look green or crusty. Take a photo of the terminal strip before you touch anything. Those three checks narrow the problem quickly.
Where DIY goes wrong: keypad and intercom units run on low-voltage trigger circuits tied into the gate operator, and swapping a board with the power still live can short the operator’s control board, which costs far more than the keypad did. DoorKing harnesses also change between revisions, so a unit that matches on the outside may not match inside. If the keypad has power but won’t trigger the gate, that’s the point to call us at (844) 320-7587 and let a technician trace the circuit. Estimates are free, and the price is written before any work starts.
FAQs
Expect seven to twelve years from a keypad membrane and ten to fifteen from the board, though the desert climate shortens the outer hardware. The ultraviolet light and summer heat here dry out the gaskets and buttons faster than in cooler regions, so membrane replacement often comes before the electronics fail. When the membrane goes, we replace it and photograph the terminal condition for your job record.
Usually yes. Most failures we find in Boulder City are the membrane, the gasket, the speaker, or a corroded terminal, all of which can be repaired without replacing the whole unit. A full replacement is only necessary when the circuit board is damaged or the model is no longer supported. We tell you which one it is on the written quote before any work starts.
A membrane or speaker replacement usually takes under an hour; a full keypad and intercom replacement typically runs one to two hours. We test the gate through at least two full open and close cycles before we leave and leave you a photo log of what was replaced and what the new settings are. Call (844) 320-7587 for a free estimate and we’ll give you a specific time window.
We match the part to your model number and revision letter, which we read from the label inside the housing or from a photo of the terminal strip. From there we source either the OEM part or a quality aftermarket equivalent, show both prices on the written quote, and let you choose. No stock of parts is kept on a truck; the part is ordered to your unit and scheduled when it arrives. Boulder City homeowners can call (844) 320-7587 for a free estimate, and every visit gets the documented photo record under the Haven Standard.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City and nearby areas.