Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Access Control Installation: The Boulder City Owner’s Guide
Ghost Controls access control installation in Boulder City typically runs $340 to $780 installed when the entry keypad, exit device, receiver, or safety accessory is added to an existing Ghost Controls operator, and most of that work can be scheduled within the same week you call. A failed part usually shows itself one of three ways: the gate stops answering the keypad, the wireless transmitter drops out past a certain distance, or the operator runs but never completes a full cycle. Boulder City owners tend to notice it on the way out, gate half-open behind them.
We’re Vance Gate Repair Boulder City, an independent service provider. We’re not affiliated with Ghost Controls, and we don’t claim to be; we’re simply one of the local companies that works on their operators and their accessory stack.
Key takeaways:
- Installed accessory pricing for a Ghost Controls system in Boulder City generally lands between $340 and $780.
- The written price is in your hands before any tool comes out.
- Every visit ends with a photo record of the part number, wiring, and settings.
- A live person answers the phone at any hour.
Which Ghost Controls Models This Applies To
Ghost Controls builds its residential line around the AXS, TSS, and DTP series, plus the accessory pieces most owners end up replacing: the AXWK wireless keypad, the ABB or AXT transmitter line, the photo-eye pair, and the receiver board inside the control box. Compatibility is more specific than a lot of aftermarket listings suggest. The wireless keypad and the receiver need to be on the same frequency family, and mixing a newer transmitter with an older receiver board will sometimes pair once and then fail intermittently, which is a compatibility problem, not a range problem.
Identify your setup before ordering anything. The model plate sits inside the operator housing, usually on the control-box lid or the arm bracket, and the transmitter frequency is printed inside the battery cover. The AXS series is the one most common on newer installs, but plenty of Boulder City properties still run the earlier TSS operators, and the accessory kits are not always interchangeable across those lines.
OEM versus aftermarket is a real decision here. Ghost Controls’ own accessory parts are matched to their control boards and their manuals, which matters most on the receiver and the keypad. A quality aftermarket photo-eye pair works fine with a matching relay, and we’ve fitted plenty. But a cheap no-name keypad with a cloned transmitter will often drop out at the distances common on desert lots. On a Boulder City driveway that reaches the property line, that difference shows up quickly.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Access Control Installation Is Failing

- The keypad lights up but the gate doesn’t move. Usually a dead receiver or a code the control board no longer holds after a power blip. If the handheld remote still works and the keypad doesn’t, the receiver or keypad wiring is where we look first.
- The remote only works close to the gate. Transmitter battery is the easy check; the harder cause is a receiver or antenna position that’s lost its ground plane after a mount loosened. We photograph the antenna run so the next technician doesn’t start from zero.
- The gate stops partway and reverses. On these operators, the photo-eye pair (the infrared beam that halts travel when something crosses it) is the first part tested. Sun exposure and blowing dust knock those sensors out of alignment more than most owners expect.
- The control board clicks but nothing happens. A failing relay or a corroded terminal on the accessory loop. In our experience, this shows up most often after the monsoon stretch, when humidity finally gets into an enclosure that hasn’t been opened in a while.
- Intermittent operation with no pattern. Loose low-voltage connections, a marginal transformer, or two transmitters fighting over one code. This is the case where a documented wiring diagram earns its keep.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Ghost Controls access control accessories in Boulder City depends on three things: the part itself, whether the low-voltage wiring is already in place, and whether we’re troubleshooting a fault or simply swapping known-good parts.
| Work | Typical installed range |
|---|---|
| Wireless keypad (AXWK-style), existing wiring | $340 – $460 |
| Receiver board or transmitter replacement | $360 – $520 |
| Photo-eye pair replacement and realignment | $380 – $540 |
| New low-voltage run to a keypad or exit device | $520 – $780 |
Parts and labor are itemized on the written estimate, so you see the hardware line and the labor line separately. That estimate is in your hands before work starts. The job is covered by our 365-Day Done Right Promise: if the repair isn’t right within a year, we make it right at no additional charge. Every visit includes a photo record at no extra cost, showing the part number installed and the settings we left.
DIY or Call Us?

Some of this is genuinely safe to check yourself. Transmitter batteries, the model plate inside the housing, cleaning dust off the photo-eye lenses, and confirming the keypad actually powers up are all fine. None of that involves line voltage or a spring under tension.
Where DIY goes wrong is at the control board and the low-voltage connections. A misplaced jumper on a receiver, a terminal tightened onto the wrong lug, or a keypad wired to a transformer that isn’t rated for it can damage the board, and the board costs more than the accessory you were trying to replace. If the operator’s wiring is compromised or the enclosure shows corrosion, this stops being a parts swap. We’d rather look at it than have you chase it.
Call (844) 320-7587 and we’ll tell you what we think before anyone comes out.
FAQs
Expect five to eight years from a well-installed keypad or receiver in this climate, and shorter for photo-eyes exposed to full afternoon sun. The heat cycling and wind-blown dust around Boulder City accelerate lens clouding and test battery life harder than humidity does, so a sensor mounted facing west will usually fade before one in shade. Call (844) 320-7587 if you’re seeing the first signs and we’ll give you a straight answer on whether it’s worth replacing now or later.
Sometimes. A misaligned photo-eye or a corroded terminal is usually a repair, not a swap, and we’ll say so if that’s what we find. A failed receiver board or a keypad with moisture damage inside the housing is a replacement. We don’t steer toward new hardware when a reset and a reseal will do the job. Call (844) 320-7587 for an honest read.
Most keypad and receiver replacements are done in 45 minutes to two hours, depending on whether the low-voltage run is intact. A new wiring run to the property line takes longer, and we’ll quote that separately from the part itself, in writing, before anything starts. Call (844) 320-7587 to schedule.
We match the part to your operator’s model and frequency family, not to a generic listing, and the exact part number goes on your written estimate and your photo record. Vance Gate Repair services nine automation brands, including LiftMaster, Mighty Mule, and DoorKing alongside Ghost Controls, so we’re never pushing a replacement operator just because we don’t recognize yours. Call (844) 320-7587 and we’ll confirm what your system needs.
If your Ghost Controls keypad has stopped answering, your photo-eyes won’t hold alignment, or you’re not sure which series you’re running, call (844) 320-7587 for a free estimate. A live person answers at any hour, and the price is in writing before we touch the gate.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City and nearby areas.