A Vance company - serving Boulder City, NV

Ghost Controls Hinge & Roller Replacement in Boulder City, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Hinge & Roller Replacement: The Boulder City Owner’s Guide

We replace failed hinges and rollers on Ghost Controls driveway gates in Boulder City, and most jobs run $140 to $320 installed depending on how many hinge points and rollers are worn and which gate series you have. Because this is a repair with real safety stakes, we quote the written price before any work starts and can usually get to you the same day. You’ll know it’s time when the gate starts dragging at the latch, the arm strains to close it, and the roller starts leaving a mark on the track instead of rolling clean.

Call (844) 320-7587

Because this is a repair on a powered gate, a failed hinge puts load on the operator and can let the gate sag onto a child or pet before anyone notices. That’s why we photograph the hinge positions, the roller contact points, and the operator limits on every visit, and why we won’t leave a gate swinging on a hinge we know is worn.

Which Ghost Controls Models This Applies To

Ghost Controls builds several gate opener lines, and hinge and roller hardware varies across them. The single most common compatibility mistake we see in Boulder City is a homeowner ordering a roller for a Ghost Controls double-gate system and finding it doesn’t fit the post-side track on their single-gate install. The parts look nearly identical in a photo and share no cross-reference in the listings. Measure before you order.

Identify your setup three ways: the model label on the operator housing, the gate leaf width and weight, and the existing hinge center-to-center spacing. If the label is sun-faded (common after a few Nevada summers), measure the hinge pin diameter and the roller wheel diameter and width with a caliper. Ghost Controls rollers typically fall in a narrow bore range, and a wheel that’s off by a millimeter will bind on the track.

On OEM versus aftermarket: Ghost Controls OEM parts match the original fit exactly, which matters when the gate has been in service for years and the track has worn to one profile. Quality aftermarket equivalents cost less and hold up fine on hinges, but we won’t put a generic roller on a worn track without checking the contact line first. We’re an independent service provider here in Boulder City and not affiliated with Ghost Controls; we work on nine major brands, including LiftMaster, Mighty Mule, and DoorKing, alongside Ghost Controls.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

professional gate repair service
Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

Hinge and roller failure rarely announces itself. It shows up as small changes in how the gate moves, and each one points to a different root cause:

  • The gate drags or catches at the latch. A worn hinge pin lets the leaf drop a fraction of an inch, and gravity does the rest. Left alone, the drop puts torque on the operator arm and shortens the life of a more expensive part.
  • The roller squeals or leaves a flat spot on the track. The wheel bearing has lost its grease or is binding. A flat-spotted roller scrubs the track with every pass, so it wears the track and the roller at once.
  • The gate wobbles side to side when you push it by hand. Hinge bushings have worn oversized. The gate still opens, so it gets ignored, but a loose hinge turns a small repair into a whole-leaf job.
  • The operator strains or reverses on close. The gate is out of alignment at the hinge, so the opener is fighting the sag. If the operator reverses and beeps, the hinge is often the cause, not the motor.
  • Visible rust bloom or a cracked hinge plate. A cracked plate is a structural failure. We’ve pulled cracked hinge plates off gates in Boulder City after a few dry summers, and one plate carrying a gate is a safety issue, not a cosmetic one.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
BeforeBefore
AfterAfter

Replacement Cost & What’s Included

Installed hinge and roller replacement in Boulder City usually lands between $140 and $320. What drives the range: how many hinge points are worn, whether the track needs straightening, the part grade you choose, and whether the operator needs a limit readjustment afterward because the gate now hangs at a different angle.

Line item Typical installed range
Single hinge replacement (one point) $45 – $85
Full hinge set (two to three points) $120 – $220
Roller replacement (per roller) $40 – $75
Track adjustment or straightening $30 – $60
Complete hinge and roller pack, one gate $140 – $320

The part price and the labor price are separate lines on the quote, and the quoted total is written down before we touch the gate. Under Clause 4 (Evidence on every job), every visit includes a documented photo record at no additional charge. Work is covered by our 365-Day Done Right Promise: if the repair isn’t right, we fix it within that year at no fee. Call (844) 320-7587 for a free estimate.

DIY or Call Us?

Technician applying sealant to a weathered metal gate post cap repair
DIY or Call Us?

Some checks are safe for an owner. Power the operator off at the control box, then swing the gate by hand. If it binds, wobbles at the hinge, or the roller skips instead of rolling, you’ve confirmed the hinge/roller problem without touching a powered gate. Do that much, then stop.

Where DIY goes wrong: a gate leaf can weigh well over a hundred pounds, and pulling the bottom hinge out without supporting the leaf drops the gate onto whatever’s beneath it. Power the operator off and a heavy unsupported gate can still crush a hand or a foot. We’ve also seen a gate re-hung on a new hinge and a re-motorized gate both left out of alignment because the operator limit wasn’t reset, which puts the motor into constant reversal. This is one of the parts where the honest call is to hand it over. The tools and the two-person lift matter, and so does the limit reset afterward. Call (844) 320-7587 and we’ll quote it in writing.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Need Gate Repair help nationwide? Licensed & insured · within the hour response · free estimates
Call (844) 320-7587
Local Service Coverage

Request a Free Estimate in Boulder City

Tell us what you need - Vance Gate Repair Boulder City responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch