Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Sunrise Manor
If your driveway gate is dragging, leaning, or rattling in the wind, the fix starts with knowing which part actually failed. We handle Gate Parts & Welding for Sunrise Manor homeowners – hinge replacement, post replacement, rail repair, and custom welding – with a written price before anyone picks up a tool. We know this side of the valley well: the ranch tracts off Lamb Boulevard, the older blocks near Sunrise Mountain, the 89110 properties where gates were hung decades ago and never re-set. When a spring gust takes a gate down, call (844) 320-7587 and a live person answers, day or night. You’ll get a flat price in writing and a photo record when we leave.
Why Vance Gate Repair Boulder City Is Sunrise Manor’s Preferred Gate Parts & Welding Company
Most of the gates we open in Sunrise Manor were hung before modern safety standards existed, and the parts on them have been patched, bent, and re-bolted more than once. We’re the crew that documents what’s actually there – the hinge that’s seized, the control board that’s obsolete, the post that’s rotted below grade – instead of guessing and replacing blindly. That habit comes from commercial access-control work that carried over to every residential driveway gate we touch. Under The Haven Standard, every Sunrise Manor job gets a written scope, a written price, and photographic evidence on the day.
What homeowners here tell us they want is simple: evidence. They’ve read the reviews, they’ve had a verbal estimate before, and they want the number on paper before anyone starts. That’s Clause 1 of the Haven Standard – have it in writing – and it holds on every visit. If a repair isn’t right, the 365-Day Done Right Promise gives us a full year to make it right at no extra charge. Our technicians have up to 12 years of experience, and we service nine major automation brands, including the LiftMaster and Linear operators that dominate older Sunrise Manor properties. A live person answers our phone at any hour, so no voicemail loop stands between you and a straight answer.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Sunrise Manor

Sunrise Manor’s gate work is mostly a fight against age and desert weather. The 1960s – 80s ranch homes here sit on shallow desert post footings, and many driveway gates were originally hung on 4×4 wood posts set only 18 – 24 inches deep. Decades of spring gusts over 50 mph have torqued those posts into the leaning, rust-locked hinge posts we find today. Here’s how we handle the four jobs that come up most.
Hinge Replacement in Sunrise Manor
When a gate swings hard, drags on the ground, or won’t latch, the hinges are usually the culprit – or the first visible symptom of a post that’s moved. Rust-locked hinges on 1970s and ’80s gates seize solid after years of desert dust and 110°F heat, and a seized hinge pulls the whole panel out of square. We replace the hinge, re-set the alignment, and photograph the new hardware position before we leave. Hinge replacement in Sunrise Manor typically runs $95 – $220 per hinge depending on gate weight and whether the hinge plate needs welding.

Post Replacement in Sunrise Manor
A sagging gate usually points to a rotting wood hinge post below grade, not the panel itself. That’s the most common real fault we find here: the gate looks fine, but the post has shifted after a windstorm pushed the whole gate sideways. We dig out the old footing and re-set a steel or deeper-set hinge post in concrete, then re-hang the hardware so the gate swings true. Post replacement in Sunrise Manor typically runs $350 – $850 depending on post depth, footing size, and whether the gate is a single swing or a double.

Rail Repair in Sunrise Manor
Sun-baked wood goes brittle, and a brittle rail cracks at the fasteners first. We splice, sister, or replace damaged rails and re-brace the frame so the gate stops flexing every time it moves. Rail repair in Sunrise Manor typically runs $150 – $420 depending on how many rails are damaged and whether the gate is wood or welded steel.

Custom Welding in Sunrise Manor
Bent frames, cracked hinge plates, and broken weld joints on steel gates get repaired at the joint, not swapped out for a new gate. We weld on-site and document the repair with a photo record and the part or plate we installed. Custom welding in Sunrise Manor typically runs $120 – $400 for a small repair, more for a full frame re-weld.
Before
AfterTrusted Brands We Service in Sunrise Manor
Older Sunrise Manor properties tend to carry legacy operators – LiftMaster and Linear swing and slide motors that have been running since the ’90s, plus the DoorKing and Elite boards that show up on light-commercial gates along the major roads. We service all nine major automation brands and don’t steer anyone toward a replacement when a repair will do. We don’t stock parts locally; the first visit is diagnostic, and parts get ordered to match the brand and model we find. That means one diagnostic visit, a written quote, then a scheduled return with the right part in hand – and a documented photo record on both.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Parts & Welding Problems We See in Sunrise Manor Homes

- Rotting wood hinge posts below grade. The gate looks fine until a 50 mph spring gust pushes the whole panel sideways, because the post has quietly rotted for years. A qualified local pro digs out the old footing and re-sets a steel or deeper-set hinge post in concrete before re-hanging the hardware.
- Rust-locked hinges and latches on ’70s – ’80s gates. Years of desert dust and 110°F heat seize these solid, and a seized hinge pulls the panel out of square until it drags on the ground. We replace the hinge, re-set the alignment, and photograph the new position.
- Obsolete control boards on legacy operators. Older LiftMaster and Linear boards lose logic and can’t be re-flashed. We check whether the board can be sourced, or whether an entrapment-protection retrofit on the existing motor is the cheaper answer.
- Dead safety photocells. A photo-eye (the infrared beam that stops the gate if something crosses the path) that no longer trips is an entrapment hazard, not a nuisance. We test the beam, replace the unit, and confirm the gate reverses under Clause 4’s evidence requirement.
Pricing for Gate Parts & Welding in Sunrise Manor, NV
Here’s what the work actually costs in this market, with the price written and handed over before any tool comes out. These are typical ranges, not teasers:
- Hinge replacement: $95 – $220 per hinge
- Post replacement: $350 – $850
- Rail repair: $150 – $420
- Custom welding: $120 – $400 for small repairs, more for a full frame re-weld
- Safety photocell replacement on a legacy operator: $140 – $280
What moves the number: gate weight, whether a hinge plate needs welding, post depth and footing size, and whether the operator is a legacy board that needs sourcing. Estimates are free, and Clause 1 of the Haven Standard means the price you agree to is the price you pay – no surprise invoice at the end. Call (844) 320-7587 for an exact quote in writing.
We Also Serve Cities Near Sunrise Manor

We serve Sunrise Manor and the surrounding east valley. If you’re just across the line in Whitney, Winchester, Las Vegas, or North Las Vegas, the same written-price, photo-record process applies. Sunrise Manor is our home base for this stretch of the valley, and we regularly work across the surrounding neighborhoods and the major roads that connect them. Wherever you are, the call is the same: (844) 320-7587.
Serving Sunrise Manor, NV – Our Local Coverage Area
We serve Sunrise Manor and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Sunrise Manor

The hinge post is almost certainly the problem, not the panel. On a typical Sunrise Manor swing gate, the panel drags and the latch won’t catch, and the real fault is a rotted wood hinge post that has shifted below grade after a windstorm pushed the whole gate sideways. A qualified local pro digs out the old footing, re-sets a steel or deeper-set hinge post in concrete, then does sag correction on the rails and re-hangs the hardware so the gate swings true again. Call (844) 320-7587 for a free estimate.
Often, yes – especially on legacy LiftMaster and Linear operators where the motor still runs and only the safety circuit has died. A dead safety photocell or a missing entrapment-protection device can usually be retrofitted onto the existing operator rather than swapping the whole unit. The honest answer depends on the board: if it can’t be sourced or re-flashed, replacement becomes the cheaper long-run call, and we’ll tell you which in writing. Call (844) 320-7587 for a free estimate.
Welding fixes the joint; replacing the gate rebuilds everything. For a bent frame, cracked hinge plate, or broken weld on a steel gate, welding at the joint is usually the cheaper answer and gets you back to true swing without a new panel. Replacement makes more sense when the frame is warped beyond correction, multiple rails are split, or the gate is wood that’s gone brittle from decades in the sun. We’ll price both in writing so you can compare. Call (844) 320-7587 for a free estimate.
Because the posts were set shallow and the wind finally won. Sunrise Manor’s ranch homes sit on shallow desert footings, and many gates were hung on 4×4 wood posts set only 18 – 24 inches deep, so decades of spring gusts over 50 mph torque those posts into leaning hinge posts. The first big gust takes down the gate that was already leaning. The fix is a deeper-set steel or concrete-set post, not a patched hinge. Call (844) 320-7587 for a free estimate.
Yes – slide gates use different hardware, including a rack and pinion, rollers, and guide posts rather than hinges. On a slide gate with an aging Linear or LiftMaster operator, a routine visit often turns up a seized rack and pinion or a safety photocell that no longer trips, alongside the guide post being out of plumb. We carry the diagnostic tools and order the brand-matched part. Call (844) 320-7587 for a free estimate.
If your gate is leaning, dragging, or you’re not sure which part actually failed, call (844) 320-7587 for a free estimate. A live person answers 24 hours a day, seven days a week. You’ll get a flat price in writing before any work starts, a photo record when the technician leaves, and the 365-Day Done Right Promise behind the repair. Bring us any written estimate from another company and we’ll review it at no cost as a free second opinion.
Written by the team at Vance Gate Repair Boulder City.