Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHinge & Post Repair in Boulder City, NV
Hinge and post repair in Boulder City typically costs $150 to $450 for a single hinge, hinge set, or post reset, and most swing gates are working again the same day. Hinges carry the full weight of the gate leaf every time it opens, and posts take the leverage that weight creates. When either one gives, the gate sags, drags on the ground, or stops latching, and the motor starts working harder than it should. We repair the hinge and post assembly itself rather than talking you into a new gate, and we hand you a written price before anyone picks up a tool.
Vance Gate Repair Boulder City works on swing gates and automated gates across the city. If you need the broader category, start with Gate Repair, and come back here when the problem is specifically the hinge side or the posts. Call (844) 320-7587 and a live person answers, any hour.
What sets our hinge and post work apart is documentation. Every visit leaves a photographed record of what we found, what we set, and what we installed. That habit came out of commercial access-control work and it applies to a residential driveway gate in Boulder City the same way: a photo of the hinge before, a photo after, and a written part number in the job file.
Key Takeaways
- Most single-hinge and post repairs in Boulder City run $150 to $450; full hinge replacement on a wide gate runs higher.
- Sagging, dragging, and a gate that won’t latch are the three most common hinge and post symptoms we see.
- We price in writing before work starts and leave a photo record of every adjustment.
- Every completed repair is backed by the 365-Day Done Right Promise.
- Bring a written estimate from another company and we’ll review it at no cost.
When You Need Hinge & Post Repair

Hinge and post failures rarely announce themselves. They build up over months of heat, wind, and daily use. Here are the scenarios where we get called most often.
- The gate sags and drags on the ground. A gate that scrapes the driveway on one corner is usually a worn hinge pin or a hinge plate pulling loose from the post. In Boulder City, the summer heat and dry air work on wood posts and painted steel alike, and the hinge side takes the most abuse.
- The gate won’t latch without lifting. When you have to lift the gate to get the latch to catch, the hinge side has dropped. That’s a hinge or post problem, not a latch problem, and fixing the latch alone won’t hold.
- A post is leaning or has pulled loose. Concrete footings crack and shift over time, especially where irrigation or drainage runs near the base. A leaning post throws off the whole gate geometry, and no amount of hinge adjustment will fix it until the post is set right.
- The hinge plate is torn or the welds are cracked. Heavy gates on thin posts put stress on the weld where the hinge plate meets the gate frame. Cracked welds are a structural problem and need to be cut out and rewelded, not patched.
- The gate swings crooked or binds at the top or bottom. When the top hinge and bottom hinge are no longer aligned, the gate binds through its arc. We measure and reset the hinge line so the gate swings true.
- The motor strains or reverses on a gate that used to move freely. Automated gates on LiftMaster, Elite, or DoorKing arms will fault out when the gate leaf drags. The motor is usually fine; the hinge and post assembly underneath it is the real culprit.
Before
AfterOur Hinge & Post Repair Process
Here’s how a hinge and post repair goes from the first call to the documented handoff.
- Phone triage and a written scope. A live person answers and asks the questions that narrow the problem: does the gate drag, does it latch, is the post leaning. We give you a written scope and a written price before anyone is dispatched.
- On-site inspection with photos. The technician photographs the hinge side, the post base, and the gate swing arc. We check the hinge pins for play, the plates for cracks, and the post for lean using a level, not a guess.
- Confirm the written price. If the inspection turns up something the phone cannot see (a cracked footing, a torn weld), we hand you an updated written price before work starts. No work happens at a price you haven’t seen in writing.
- Repair the hinge, the post, or both. Depending on what we find, that means replacing hinge pins and plates, resetting or re-anchoring a post, rewelding a torn plate, or shimming and realigning the gate leaf so it swings freely.
- Test the swing and the latch. We open and close the gate through its full arc, check the latch engagement, and confirm the gate moves without drag before we leave. On an automated gate, we re-check the arm and the limits so the motor isn’t fighting the gate.
- Document and hand off. You get a photo log of every adjustment, the part number of anything replaced, and a written record of what we found and what we set. That record stays in the job file.
Hinge & Post Repair Pricing in Boulder City

Hinge and post repair in Boulder City runs $150 to $450 for most single-hinge or post-reset jobs. Wide gates, double gates, and jobs that need a footing repaired or a weld cut out and redone land higher. Here’s what the line items look like.
| Repair | Typical Range |
|---|---|
| Single hinge pin or plate replacement | $150 – $250 |
| Full hinge set replacement (both hinges) | $250 – $400 |
| Post reset or re-anchoring (existing footing intact) | $200 – $450 |
| Reweld torn hinge plate | $175 – $350 |
| New post and footing (post compromised) | Quote after inspection |
What drives the price: the number of hinges being replaced, whether the post footing is intact or needs rework, whether the gate is steel, wood, or aluminum, and whether the weld needs to be cut out and redone. A single hinge pin on a light aluminum gate is on the low end. A wide steel gate with a torn plate and a leaning post is on the high end.
Every price is written before work starts. Under the Haven Standard, that’s Clause 1: have it in writing. If you have a written estimate from another company, bring it and we’ll review it at no cost, because a second opinion should never cost you anything. Free estimates are standard on every call.
For the full range of gate work in the city, see Gate Repair in Boulder City.
What Affects Hinge & Post Repair Cost
- Number of hinges. Replacing one hinge is cheaper than replacing the full set. We usually recommend replacing both at once when one has failed, since the second is usually on the same wear curve.
- Post condition. A post with a solid footing can be reset. A post with a cracked or shifted footing needs a new footing, which is a bigger job.
- Material. Wood posts, aluminum, and steel all behave differently. Steel and aluminum welds need a different approach than wood re-anchoring.
- Gate weight and width. A wide double gate carries more leverage on the hinge side, so the hardware and the repair take more time and heavier parts.
- Whether the gate is automated. If an arm is attached, we re-check the arm and limits after the hinge repair so the motor doesn’t fight the new geometry. That extra step is part of the same written price, not an add-on.
Why Document the Repair

The reason we photograph every hinge and post repair is simple: gate problems come back. A gate that sags once will sag again if the hinge pin wears or the post shifts. When the next technician arrives with our photo record and written notes in hand, they aren’t starting from zero. You don’t pay twice to rediscover the same problem.
That documentation works on any motor already on the property. We work on LiftMaster, DoorKing, Elite, Mighty Mule, and other major gate-automation brands, so the arm and the hinge side are handled by the same company rather than split between two. If the hinge repair reveals a motor issue, we write down what we found instead of steering you toward a replacement. The repair is the job.
Repair or Replace: Hinge and Post
Most hinge and post problems are repairable, and repair is cheaper than a new gate. A failed hinge pin, a torn hinge plate, and a leaning post are all fixable on the existing gate. Replacement only makes sense when the gate frame itself is rusted through, twisted beyond re-alignment, or has been hit hard enough to bend the leaf. We tell you which one it is after the inspection, in writing, with photos of what we found.
FAQs – Hinge & Post Repair

How much does hinge and post repair cost in Boulder City?
Hinge and post repair in Boulder City typically runs $150 to $450 depending on the number of hinges, post condition, and gate material. A single hinge pin is on the low end; a full hinge set with a post reset is on the high end. Call (844) 320-7587 for an exact written quote, and estimates are free.
Can you fix a sagging gate the same day?
Most single-hinge and post-reset jobs are finished the same day, usually within a couple of hours on site. A live person answers the phone around the clock, so call (844) 320-7587 and we’ll tell you what’s realistic for your gate before anyone is dispatched.
Is it cheaper to repair the hinge or replace the gate?
Repair is almost always cheaper than replacement unless the gate frame is rusted through or twisted beyond re-alignment. A hinge repair on a sound gate preserves the gate you already own and keeps the motor and latch intact. Call (844) 320-7587 and we’ll give you the written repair price before you decide anything.
What causes a gate post to lean in Boulder City?
Post lean usually comes from a cracked or shifted concrete footing, often where drainage or irrigation runs near the base, combined with the daily leverage of the gate leaf. The summer heat and dry ground can accelerate footing movement. Call (844) 320-7587 for a free inspection and a written price to reset the post.
Ready to get your gate swinging true again? Call (844) 320-7587 for a free estimate. A live person answers any hour, the written price comes before the work, and every hinge and post repair is backed by the 365-Day Done Right Promise.
Written by the team at Vance Gate Repair Boulder City, serving Boulder City.