Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Boulder City Homeowners
A gate that won’t open, won’t close, or drags across the driveway is a repair you want handled before it becomes a fall or a security gap. Gate repair in Boulder City is what we do, and it’s the only thing we do. Our technicians have up to 12 years of experience across the nine major automation brands, and we price every repair in writing before anyone touches the gate. Same-day service is available, and a live person answers the phone around the clock. Call (844) 320-7587 and we’ll get a technician to your gate.
A lot of Boulder City gates sit on the older blocks off Nevada Way and around the Historic District, where the original hardware has been outdoor in the desert wind for years. What we find most often is a hinge that’s quietly given up an inch, or an operator stressed by a post that’s leaning. We fix the cause, not just the symptom, and we leave a photo record of every adjustment so nobody has to guess later.
What Our Gate Repair Service Includes
Electric Gate Repair
An electric gate runs on a motor, control board, and safety devices, and any one of them can fail on its own. You need this service when the gate stops responding, moves partway, or reverses for no clear reason. We test the control board, the photo-eye alignment, and the limit switches, then hand you a written price on what has to be replaced before we replace anything. In Boulder City, spring wind storms often knock a photo-eye out of alignment by a couple of inches, and that alone can stop the gate from closing.

Automatic Gate Repair
Automatic gates take the motor, the arm, and the operator chain or screw together. When they stop moving, it’s usually the operator arm bracket loosening at the post, or the limit switch drifting past the travel point. We check each of these and read the motor’s diagnostic codes, then reset the limits and photograph the new positions. If the operator is at the end of its life, we tell you that in plain terms and give you the repair price beside a replacement price, so the choice is yours.

Hinge & Post Repair
A sagging swing gate almost always traces back to the hinge or the post it hangs on. You’ll notice the gate dragging, catching on the ground, or not latching square. We re-set or replace the hinge hardware and, where the post has shifted in the soil, we address the footing so the gate hangs true again. In this climate, the soil expands and contracts with the desert heat and dry season, and a post that was solid two summers ago can work loose without a storm.

Gate Realignment
Realignment corrects a gate that’s out of square with its post, its latch, or the ground. The sign is usually a gate that closes but doesn’t sit flush, or one that bumps the stop on its way in. We measure the gap at the latch, check the gate’s plumb, and adjust the hinges and stops accordingly. On sliding gates, realignment means checking the track and rollers, which collect grit and dust faster than most homeowners expect in the open desert.
Lock Repair
Locks and latches fail from wear, misalignment, or a keyway packed with dust. You need lock repair when the key sticks, the latch won’t catch, or the gate opens but won’t stay shut. We look at whether the lock is failing on its own or because the gate has moved out of alignment, since replacing a lock on a misaligned gate just repeats the problem. We repair the latch, the strike, and the mechanism, and test the fit with the gate closed and under load.
Weld & Rust Repair
Welds crack and metal rusts, especially on older gates exposed to sun and dry air. The warning sign is a wobble at a joint, a visible rust bloom, or a piece of hardware that’s worked loose. We re-weld the joint, treat the rust, and repaint the affected section so the repair holds. On Boulder City gates, the UV exposure is brutal on paint and powder coat, so catching rust early saves the whole gate, not just the corner.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Repair

We service all nine of the major gate-automation brands, including LiftMaster, DoorKing, Elite, and Mighty Mule. On LiftMaster operators, we know the arm bracket and the limit switches are the two places that wear first, and we check both before recommending anything else. DoorKing equipment shows up often on heavier swing gates, and we know how to read its fault codes to find a control-board fault rather than guessing at the motor. On Elite and Mighty Mule, we look at the operator chain and the control box, since both are common failure points on residential installs.
Whether your gate runs on FAAC, BFT, Linear, Viking, or Ghost Controls, we can work on it. Our technicians have up to 12 years across these systems, and we don’t steer you toward replacement when a repair will do. Whatever motor is already on your property, we can help.
Before
AfterSigns You Need Gate Repair Right Now
- The gate won’t close all the way. That usually means a limit switch has drifted or the track has debris in it, and a gate that won’t close is a security gap you don’t want overnight.
- The gate reverses for no reason. A photo-eye that’s misaligned or dirty will trip the safety circuit, and the gate will think something is in its path.
- The gate drags on the ground. A dragging gate means the hinges or post have shifted, and every cycle you run it wears the hinge and the operator faster.
- The motor hums but the gate doesn’t move. That points to a chain or screw problem, a stripped gear, or a control-board fault that needs diagnosing before more parts go in.
- A hinge or weld looks cracked. A cracked weld on a swing gate is a safety issue, and it can fail without warning when the gate is under load.
Our Gate Repair Process – Step by Step

- 1
Call and tell us what’s happening. A live person answers the phone any hour. We ask what the gate is doing, what brand it is, and when it started, so the technician arrives ready for the likely fault.
- 2
We diagnose on site. We test the operator, read the diagnostics, check the photo-eye, and put a level on the post. We photograph the readings before we change anything.
- 3
You get a written price before work starts. Under The Haven Standard, the flat price is written and handed to you before we pick up a tool. No surprise invoice at the end.
- 4
We do the repair. Once you approve, we complete the work and test the gate through a full open-and-close cycle, plus a safety reverse test.
- 5
We document and hand off. You receive a photo log of what was found, what was adjusted, and what part was installed. It’s filed in the job record so no future technician has to rediscover the same problem.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Boulder City?
A typical gate repair in Boulder City runs $150 to $450, depending on what failed and how deep the fix goes. A hinge adjustment or lock repair sits at the low end. A limit switch reset or photo-eye realignment usually lands between $180 and $280. An operator-arm or control-board replacement runs $300 to $650, and a weld-and-rust repair on a swing gate depends on how much metal needs cutting out.
What moves the price: the brand of the operator, whether the post footing needs work, and whether the failure is mechanical or electrical. A gate that’s out of alignment often costs less to fix than one with a failed control board, because the labor is the same but the parts aren’t. You can avoid overpaying by getting a written price before anyone starts, and by asking for the part number on anything replaced. That’s how you check the invoice against the quote.
Every estimate we give is free, and it’s written, not verbal. It covers the diagnosis, the part numbers, the labor, and the total, and it’s not a range that creeps upward mid-job. Bring a written estimate from another company and we’ll review it at no cost, as a second opinion.
Gate Repair Near Boulder City – Our Service Area

We cover Boulder City and the surrounding neighborhoods, including Henderson, Whitney, Paradise, and Enterprise. Technicians are dispatched from local routes, so response times stay short through the day, and we handle emergency calls around the clock. If you’re east of town, in Sunrise Manor or Winchester, we can usually reach you the same day you call. For a closer look at coverage, see our Gate Repair in Boulder City page.
Serving Boulder City, NV – Our Local Coverage Area
We serve Boulder City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Repair in Boulder City

Gate repair is the work of fixing what’s keeping a gate from opening, closing, or securing reliably. It covers the operator and motor, the hinges and posts, the alignment, the lock and latch, and any weld or rust damage on the gate itself. At Vance Gate Repair, we diagnose the cause, give you a written price, and complete the repair with a photo record of everything we found and changed.
Most gate repairs are completed in a single visit, usually within one to three hours. A hinge adjustment or limit-switch reset can finish in under an hour. A control-board replacement or post footing repair may run longer, and we tell you the time estimate alongside the written price before we start. If a part has to be ordered, we schedule the return visit and confirm the time with you.
Most gate repairs in Boulder City run $150 to $450, with common fixes like limit-switch resets and photo-eye realignments between $180 and $280. The exact price depends on the brand, the part, and whether the post or footing needs work. You get the flat price in writing before any work begins, so the invoice matches the quote. Call (844) 320-7587 for an exact price.
Yes. We service all nine major brands, including LiftMaster, DoorKing, Elite, Mighty Mule, FAAC, BFT, Linear, Viking, and Ghost Controls. Our technicians know where each brand wears out, so the diagnosis starts from experience rather than guesswork. Whatever operator is already on your gate, we can work on it.
Yes. A live person answers the phone 24 hours a day, seven days a week, and we handle emergency gate repair in Boulder City around the clock. That includes gates stuck open overnight, gates that won’t close, and any situation where the gate is a security risk. Call (844) 320-7587 and we’ll dispatch a technician.
Every repair is covered by our 365-Day Done Right Promise. If the repair isn’t right within one full year, we make it right at no additional charge, with no argument and no expiration inside that window. The promise applies to all completed work, and the written price and photo record stay in the job file so the coverage is easy to verify.
Clear the gate’s path and the area around the operator so the technician can work safely, and unlock any manual release if you know where it is. Have the brand name and model of the operator handy if you can, plus the written estimate if another company gave you one. If the gate is stuck open, keep pets and kids clear of the swing path until we arrive.
Schedule Your Gate Repair Service in Boulder City Today
A gate that’s misbehaving won’t fix itself, and the longer it drags or sticks, the more it wears on the operator. Call (844) 320-7587 for a free, written estimate in Boulder City. A live person answers any hour. You’ll get the price in writing before work starts, a photo record when we’re done, and the 365-Day Done Right Promise behind every repair. Our Gate Repair in Henderson page and our Gate Repair in Whitney page cover the nearby cities we serve.
Written by the team at Vance Gate Repair.