Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Parts & Welding for Boulder City Homeowners
When a gate hinge tears loose from the post or a sagging rail drags the ground, the whole property feels wrong: the gate shudders, the latch misses, and the motor works twice as hard to force a swing that used to glide. We’re Vance Gate Repair Boulder City, and gate parts and welding are what we do most. Our technicians have up to 12 years of experience, and we’ve handled more than 22,000 gates since 2014. We answer the phone as a live person 24/7, so if your gate is hanging off a hinge right now, call (844) 320-7587 and we’ll get a technician to you in Boulder City with a written price before anything starts.
What Our Gate Parts & Welding Service Includes
Gate parts and welding cover the physical hardware of the gate itself, separate from the motor and the access-control electronics. It’s the sagging hinge, the leaning post, the bent rail, the gate that won’t quite latch. Here’s what each piece of the service looks like in practice.
Hinge Replacement
Hinges carry the full weight of a swing gate and take the most load when the gate opens and closes thousands of times a year. You know a hinge is failing when the gate drops at the outer edge, squeals on the swing, or the pin has worn a visible slot into the leaf. We remove the worn hinge, check the hinge-side frame for cracked welds, and weld or bolt on a replacement rated for the gate’s weight. Every hinge swap ends with a photo of the pin seated flush and the gate swinging clean.

Post Replacement
A gate post is only as strong as its footing, and in Boulder City’s sun-baked desert soil that footing moves. Posts lean when the concrete base cracks, the anchor plate rusts through, or the soil has washed out under a drip line. We cut out the old post, set a proper footing, and reset the gate so the post is plumb in both directions before we weld the hinge plate back on. Before we leave, we photograph the level reading and the new footing so there’s a record of how it was set.

Rail Repair
Rails are the horizontal bars of the gate frame, and a bent rail throws the whole leaf out of square. Impact damage, rust creep at the weld joints, and the slow sag that comes from a gate built too light for its span all hit the rails first. We straighten where straightening will hold, and if the steel is compromised we’ll cut out the damaged section and weld in new stock so the rail is true again. The gate should close into its latch without you lifting it by hand.

Custom Welding
Custom welding covers the one-off jobs: a gate leaf that no longer fits its opening after a property change, a broken picket spacer, a driveway gate widened a few inches, or a cracked weld on a finial that’s been rattling for a season. We weld steel, not ornamental cast iron shortcuts, and we match the finish as close as the existing metal allows. Every weld is cleaned, inspected, and photographed for the job record, which is what the Haven Standard calls evidence on every job.
Gate Rollers
Sliding gates ride on rollers or truck wheels, and when those wear the gate grinds along the ground and the operator strains. Worn rollers show up as a jump at one end of travel, a scraping sound on the track, or a gate that only closes if you nudge it by hand. We pull the old rollers, clean the track, and fit new ones sized to the gate’s weight, then check the gate for true tracking across its full run. If a roller seized because the track is bent, we address the track too.
Latch & Lock
A latch or lock that won’t catch is often a symptom, not a cause: the gate out of square, the post shifted, or the striker misaligned by an inch. We check alignment before we touch the latch itself, because a latch that keeps loosening is usually fighting a gate that’s moved. Then we rebuild or replace the latch and lock, set the striker at a position that holds under load, and test it with the gate opened and closed by hand and by the motor.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Parts & Welding

We work on the automation and hardware already on your property rather than steering you toward a replacement. That means we’ve put hands on a lot of LiftMaster operators where the gate leaf binds against a sagging hinge and the motor gets blamed for a hardware problem. We know how Mighty Mule and DoorKing installations are built and where their brackets attach, which matters when a post needs to move and the operator has to be re-set afterward.
An Elite swing operator, a DoorKing slide operator, or a LiftMaster arm all care about the same thing underneath: whether the gate swings free and square. When the hardware is right, the operator has less to fight. Whether you have DoorKing, Mighty Mule, LiftMaster, or any other make, we can help.
Before
AfterSigns You Need Gate Parts & Welding Right Now
Some of these are nuisance sounds; some mean the gate is a hazard waiting for a windy day. None of them get better on their own.
- The gate drops at the outer edge. That’s usually a worn hinge or a weakening post, and the full weight of the leaf is now hanging on the latch. Left alone, the sag gets worse and the hinge eventually tears free.
- You can see rust bleeding at a weld. Rust at a weld joint means moisture is sitting inside the joint where you can’t see it. The weld is thinning from the inside, and it will fail under load rather than slowly.
- The gate scrapes or grinds on the ground. On a sliding gate that’s usually a worn roller or a bent track. Grinding wears the gate, the track, and the operator all at once, so the repair gets more expensive the longer it runs.
- The latch won’t hold or keeps loosening. A latch that keeps backing off is telling you the gate has moved out of square. Tightening the screws is a two-day fix at best.
- The gate no longer meets the post squarely. Gaps at the top or bottom of the gate that weren’t there before point to a post issue or a racking frame. If the gate is out of square, the operator will start pushing the gate into the stop and the motor will wear out.
Our Gate Parts & Welding Process – Step by Step

- 1
Phone call and triage. A live person answers at any hour, so we can talk through what’s happening and decide whether this is a same-day repair or a scheduled one. We’ll tell you what we expect to find based on what you describe.
- 2
On-site inspection with a written scope. The technician walks the gate, checks hinge pins, post plumb, rail square, rollers, and latch alignment, and writes the scope and price in writing before any work starts. That written price is the entire point of the Haven Standard: no verbal estimate, no surprise invoice.
- 3
Pull the gate off the operator if needed. Where a hinge or post repair will affect the swing geometry, we disconnect the operator first so we can swing the gate by hand and confirm the hardware moves free. This is where a lot of “motor problems” get caught as hardware problems.
- 4
Repair or weld, with photos at every stage. New hinge, reset post, welded rail, new roller, rebuilt latch, whatever the scope calls for. Every adjustment is photographed: the new pin seated, the post level, the rail true, the latch striking square. You get that photo log before we leave.
- 5
Function test and handoff. We cycle the gate open and closed under motor power and by hand, check the latch engages with a firm push, and confirm the operator isn’t straining against a stop. You get the written record of what was found, what was set, and the part numbers of anything replaced.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Boulder City?
Most gate hardware repairs in Boulder City land between $150 and $450, and that’s the number we write down before we start. Hinge replacement on a standard swing gate typically runs $150 – $300 per hinge depending on the gate’s weight and whether the hinge-side frame needs a weld repair. Rail repair and custom welding generally come in at $200 – $500 depending on linear feet and whether the gate has to come off its hinges. Post replacement is the bigger job, usually $600 – $1,600, because it includes a new footing, resetting, and re-hanging the gate. Rollers and track work on a sliding gate run $180 – $400, and latch and lock rebuilds are typically $120 – $280.
What moves the price is the weight of the gate, whether the hardware is welded or bolted, how much rust has gotten into the frame, and whether the operator needs re-setting after a post or hinge repair. The way to avoid overpaying is a written scope that tells you exactly which hinge, which rail, and which latch is being replaced, with the price attached before the first cut. That’s what makes the flat price flat: you know what’s being fixed and what it costs. Our estimates are free, and the quote you get is the price you pay unless you add work after you’ve seen the quote.
Gate Parts & Welding Near Boulder City – Our Service Area

We serve Boulder City and the surrounding area, including Whitney, Henderson, and the east valley suburbs. For gate parts and welding we schedule to the next available window, usually within a day or two, and we’ll confirm the time with you when you call. If your gate is a safety issue, tell us on the phone and we’ll treat it like one. Related services like gate repair, gate motor and opener work, and gate access control are all handled by the same technicians.
Serving Boulder City, NV – Our Local Coverage Area
We serve Boulder City and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Parts & Welding in Boulder City

Gate parts and welding covers the physical hardware of the gate itself: hinges, posts, rails, rollers, latches, and locks, plus the welding needed to repair or customize the metal frame. It’s separate from the motor and access-control electronics, although hardware problems and motor problems are often confused. If your gate has sagged, dropped, bent, or stopped latching, that’s usually a parts-and-welding job rather than a motor job.
Most hinge, roller, and latch repairs finish in one to two hours on site. A rail repair or custom welding job typically runs two to four hours, and post replacement is usually a half-day or a full-day job because of the footing and resetting. The technician will write the expected time on the scope before starting, so you’re not guessing how long the truck will be in your driveway.
Most jobs land between $150 and $500 for hinge, rail, roller, and latch work, with post replacement running $600 – $1,600. The number depends on the gate’s weight, whether the hardware is welded or bolted, and how much rust is in the frame. We write the price before we start, so the number on the invoice is the number you agreed to. Call (844) 320-7587 for an exact quote, and the estimate is free.
Yes. We service LiftMaster, Mighty Mule, DoorKing, Elite, FAAC, BFT, Linear, Viking, and Ghost Controls, plus other makes. Where a hardware repair affects the operator, we disconnect and re-set the operator after the repair is done, and the photo log shows the new position. Whether you have LiftMaster, Mighty Mule, or another brand, we can help.
Yes, we answer the phone 24/7 and can get a technician out for safety-related hardware failures like a gate hanging off a hinge or a post that’s shifted. If the gate is stuck open on a property that needs to be secured, call (844) 320-7587 and we’ll triage the situation on the phone. Not every hardware repair is a same-day job, but the ones that create a hazard get treated that way.
Every repair we complete is covered by the 365-Day Done Right Promise: if the repair isn’t right, we make it right at no additional charge within that window. That covers the work and the parts we installed, including hinges, rollers, and latch replacements. If something we welded or set fails inside the year, call and we’ll come back out.
Clear the area around the gate and the path to the work, so the technician has room to swing the gate fully and set up equipment. If you have a paper estimate from another company, bring it: we’ll do a free second opinion on any written estimate you already have, at no cost. If you’ve noticed a specific sound or symptom, note when it happens so the technician can reproduce it on the spot.
Schedule Your Gate Parts & Welding Service in Boulder City Today
Call (844) 320-7587 for a free estimate on your gate parts and welding in Boulder City. A live person answers any hour, and the technician who comes out writes the price and hands it to you before any work begins. Under the Haven Standard, you get the written scope, the photo log, and the 365-Day Done Right Promise on every job. No surprise invoice, no guesswork afterward.
Written by the team at Vance Gate Repair Boulder City.